Avatar

Ernesto Perito

  • Total activity 122
  • Last activity
  • Member since
  • Following 0 users
  • Followed by 0 users
  • Votes 30
  • Subscriptions 38
Follow

Posts

Recent activity by Ernesto Perito
Sort by recent activity Recent activity Votes
  • Answered

    Controller Unidentified problem

    1. Community
    2. Troubleshooting — FANUC

    Dear All, I am facing a problem while working on RJ-3 controller, As soon as i press the deadman switch on Teach pendant my controller  just turn off itself.  I have seen documents but couldn't fin...

    • Created
    • 3 followers
    • 2 comments
    • 0 votes
  • Answered

    Over Heating

    1. Community
    2. Mechanical Design

    Hi Everyone! I wanted to discuss the over heating of my robot, it is overheating than usual nowadays, is it something to be worried about? Is it indicating any potential failure? Any suggestions to...

    • Created
    • 3 followers
    • 3 comments
    • 0 votes

  • P300iA Zero position problem

    1. Community
    2. Troubleshooting — FANUC

    Hi, I am worried why is my robot does not returning to the zero position Correctly?  I have noticed that whenever I power down the robot at home position and start it back up it changing position, ...

    • Created
    • 3 followers
    • 2 comments
    • 0 votes
  • Answered

    Purge System Testing

    1. Community
    2. Mechanical Design

    Hi guys, Can anybody tell me what is the procedure to test for purge air leakage?

    • Created
    • 4 followers
    • 7 comments
    • 0 votes
  • Answered

    Roboguide v8.2 Error

    1. Community
    2. Troubleshooting — FANUC

    Hi friends I am trying to create a cell in Roboguide but this is the error i am getting: "The file backup requires ROBOGUIDE does not support RJ3iB Mate. You cannot create virtual robot from M6.30 ...

    • Edited
    • 4 followers
    • 3 comments
    • 0 votes
  • Answered

    Spot Errors 474, 476

    1. Community
    2. Troubleshooting — FANUC

    Hi Everyone! We have an M-20iA with R-30iB controller which we didn’t use in a while. It was placed in workshop now we needed this bad boy but all it is showing is errors. Below spot errors are i a...

    • Created
    • 3 followers
    • 3 comments
    • 0 votes
  • Answered

    Limit error(G:1, A:4)

    1. Community
    2. Troubleshooting — FANUC

    Hola, I am getting this Limit Error (G:1, A:4), i have set the limits but still getting this alarm.. does it indicates anything else than setting limits? Please Help! Thanks in advance!  

    • Created
    • 2 followers
    • 2 comments
    • 0 votes

  • LR mate 100i cable connectors

    1. Community
    2. Electrical Design

    Hi Everyone, I Urgently need Cable connectors of LR-mate. Does anyone knows where to find Cable connectors of LR Mate 100i which are on RM and RP ports of the robot.?    

    • Created
    • 2 followers
    • 1 comment
    • 0 votes
  • Answered

    compatibility of TP

    1. Community
    2. Troubleshooting — FANUC

    Hi guys, I am working on an old robot  and it has RJ2 controller it has a Teach pendant also. But I want to replace the teach pendant with a new one. A05B- 2301 - C371, I was told that this TP is c...

    • Edited
    • 3 followers
    • 4 comments
    • 0 votes
  • Answered

    SRVO 068 Alarm

    1. Community
    2. Troubleshooting — FANUC

    Hi you all, We are working on FANUC Arm M410 Series. we often get the SRVO 068 DTERR (Grp:1 Ax:4) alarms and it does not go away easily. It only get away while moving the axis slightly. Can anyone ...

    • Created
    • 2 followers
    • 1 comment
    • 0 votes