Chang Thriving

Answered

Couple of Questions related to Payload

1. Community
2. Troubleshooting — FANUC

Hi experts. I am working on my FANUC 1000iA/100F having an R30iA controller. I am making use of a vacuum gripper for gripping numerous different shaped and sized parts. I am interested to know of t...

• Created February 05, 2020 06:56
• 5 followers
• 6 comments
• 0 votes

Drilling the hole through FANUC

1. Community
2. Electrical Design

Hell everyone! I have been given a special task for working on an application which is involving the tapping and drilling of holes.  The spindle motor is already mounted over the 6th axis of its ar...

• Created January 31, 2020 11:15
• 2 followers
• 1 comment
• 0 votes

Way to do quick mastering

1. Community
2. Electrical Design

Hi experts, I have a question that while performing quick mastering, how close does one need to be near to quick mastered position taken for reference when the revolutions or joint angle of motors ...

• Created January 29, 2020 09:35
• 3 followers
• 2 comments
• 0 votes

Answered

Teach Pendent issue

1. Community
2. Troubleshooting — FANUC

Hello, I have been trying to solve the reason behind my teach pendant not displaying any job which is running. I am using FANUC R30iA mate controller.  I am in need the pendant to show the all runn...

• Created January 27, 2020 05:31
• 3 followers
• 6 comments
• 0 votes

Is there any way for creating the Jog Frame without saving steps?

1. Community
2. Electrical Design

Hello guys,  I believe I have asked this question before. I have been working on FANUC robots for over 8 months now and had no learning about it before i started working. I have been trying to crea...

• Created January 22, 2020 04:43
• 2 followers
• 1 comment
• 0 votes

Setting up hold for CC?

1. Community
2. Troubleshooting — FANUC

Hi all, I have to use the Hold CC for my project. It is mentioned in literature that "The value is the distance in millimeters from the part detect that robot can travel prior to sending the convey...

• Created January 21, 2020 08:40
• 4 followers
• 4 comments
• 0 votes

Answered

FANUC which is Ceiling Mounted

1. Community
2. Troubleshooting — FANUC

Hi all, I am in need of some real help. I am having a FANUC which is ceiling mounted. Yes, it is ceiling mounted and now I am interested to invert its world axis so that it is played normal. I have...

• Created January 20, 2020 07:45
• 3 followers
• 4 comments
• 0 votes

Answered

Requirements of Roboguide

1. Community
2. Troubleshooting — FANUC

Hello all, I am having copy of the Robo-Guide WeldPro and have not any hardware requirements for it and don't know how to run it smoothly. I wan to run it over my laptop so that i may move it all a...

• Created January 17, 2020 13:52
• 4 followers
• 4 comments
• 0 votes

Answered

Error: SRVO036 G1A3

1. Community
2. Troubleshooting — FANUC

Hello all, I am having a FANUC M710i robot having a RJ3 controller. I am getting an error of SRVO036 G1A3. This error is happening couple of times for each cycle, and i have to reset the fault and ...

• Created January 16, 2020 10:55
• 3 followers
• 2 comments
• 0 votes

Problem with changing the parameters for welding of my FANUC

1. Community
2. Troubleshooting — FANUC

Hi all, I am having some troubles with altering the parameters for my FANUC's welding. The model of my FANUC is ARCMATE 100i and its controller is RJ2. If anyone of you have any information of the ...

• Created January 14, 2020 07:38
• 3 followers
• 3 comments
• 0 votes