Frankie Ellis

Answered

Invalid indexing of values for R1=PR1,2

1. Community
2. Troubleshooting — FANUC

Hi folks, I am having a trouble here and I am not having any clue fixing it. I am here trying to get a specific value for my PR. I am using the following for getting it. R1=PR1,2 However, I am gett...

• Created January 14, 2020 05:11
• 3 followers
• 3 comments
• 0 votes

Joint Speed of FANUC

1. Community
2. Electrical Design

  Hi,  I am working on an application that a point cloud scanner is attached to the end of an old FANUC M16i with a RJ3 controller. For the generation of point cloud in a right way for the TCP spee...

• Created January 13, 2020 06:03
• 2 followers
• 1 comment
• 0 votes

Answered

help me with fixing my FANUC

1. Community
2. Troubleshooting — FANUC

Hi,  I am having FANUC S420iW and hitting is needed to shift it to about 10mm in a specific direction. What can be done in order to achieve it except changing its midpoint. How to fix this offset?

• Created January 10, 2020 07:55
• 2 followers
• 2 comments
• 0 votes

Answered

Freezing up of RJ3 TP when push control stop---need help

1. Community
2. Troubleshooting — FANUC

Hey all. I have a problem. Whenever I am having any fault, i open up the safety gates which is breaking the circuit. I am getting alarm for control stop i.e. SRVO-199, but it happens sometimes that...

• Created January 08, 2020 03:44
• 2 followers
• 5 comments
• 0 votes

Problems faced in RoboGuide

1. Community
2. Troubleshooting — FANUC

Hi, I have been using roboguide for quite a while now but facing some problems now. I have been studying material over internet and learned a lot.. Now the problem that I am facing is that i have p...

• Created December 19, 2019 06:48
• 2 followers
• 2 comments
• 0 votes

Answered

Which variable is controlling speed of FANUC holding SHIFT

1. Community
2. Troubleshooting — FANUC

Hi, i am in search of answer to question that on most of FANUCs it happens that holding SHIFT button is changing the speed to about 25 to 50 percent increment and constant increment of 5 percent if...

• Created December 18, 2019 09:23
• 2 followers
• 1 comment
• 0 votes

Answered

Startup of Fanuc Robotic arm

1. Community
2. Troubleshooting — FANUC

I recently bought my FANUC S10 and is having problem with startup. When i am turning ON its control panel over the teach pendant, then it shows some of errors when it is trying to load MAIN1027. Th...

• Created December 17, 2019 06:18
• 2 followers
• 1 comment
• 0 votes

Question related to Fanuc RJ3iC controller with an RB165F

1. Community
2. Electrical Design

I hope someone would help me with this. I am having a FANUC RJ3iC controller having an RB165F robot having 7 axis. I am having air chucks which are advancing to activate the clamp over 7th axis whe...

• Created December 16, 2019 04:58
• 4 followers
• 3 comments
• 0 votes

Answered

Is there a way for safe output from robot to pLC

1. Community
2. Mechanical Design

Hi all, I am required to pass dual channel "safe" signal to my robot's PLC but when the robot is in particular zone only. I am having a DCS capacity but it is currently not utilizing all of inputs ...

• Created December 13, 2019 05:58
• 3 followers
• 6 comments
• 0 votes

Pinouts of cables of FANUC

1. Community
2. Troubleshooting — FANUC

Hi all!I have another question that is it possible to get pinout for all cables of FANUC robot? Any help will be greatly appreciated.Thank You

• Created December 12, 2019 11:00
• 4 followers
• 3 comments
• 0 votes