Dimitry Vasilkov

Proximity Switch Connection

1. Community
2. Electrical Design

I have a robotic application in which i would like to setup something like when proximity switch is turn on ( detected ) , It will turn on the gripper function and after picking up the part , it wi...

• Edited March 03, 2020 09:11
• 2 followers
• 2 comments
• 0 votes

Answered

GUN IMPEDANCE on SPOT-TOOL

1. Community
2. Troubleshooting — FANUC

Hey All ,  I would like to have a mechanical maintenance performed on our spot-tool  R2000ib with R30iB controller. How can i verify Gun-impedance value before and after maintenance is carried out ?

• Edited February 10, 2020 12:20
• 2 followers
• 1 comment
• 0 votes

Brake Maintenance

1. Community
2. Troubleshooting — FANUC

Hey Guys ,  We are running our robot since very long time and We had minor issues related to bad fuses and cables. Now During the maintenance is there any good way to check if breaks are performing...

• Created February 09, 2020 13:05
• 2 followers
• 1 comment
• 0 votes

Answered

ARC START / WELD START

1. Community
2. Troubleshooting — FANUC

I have Arcmate - 120iD robot with R30iB controller. Before a month ago when i was doing the programming , I clearly remember , I had this option ARC START.I asked to the other operator. He said he ...

• Created February 07, 2020 15:54
• 2 followers
• 1 comment
• 0 votes

Alarm SRVO-105

1. Community
2. Troubleshooting — FANUC

Any one can help me with this alarm ? I do not have manual to look for it. How to resolve. ! Yesterday there was a fault in controller box. We changed the fuse. Is this alarm related to that ?  

• Created February 03, 2020 11:44
• 3 followers
• 2 comments
• 0 votes

DCS Update

1. Community
2. Troubleshooting — FANUC

Hello All ,  I have one question about DCS parameter change. I intend to change the three of axis motors with encoders. I am also using DCS function. So my question is , Will i  be require to retou...

• Created February 03, 2020 03:12
• 2 followers
• 1 comment
• 0 votes

Answered

Teach Pendant Screen

1. Community
2. Troubleshooting — FANUC

Hey Guys ,  I know this may be a simple question. But someone changed the screen from one part to three part. How i can get back to a single screen .!! Thank you 

• Created February 02, 2020 06:09
• 2 followers
• 1 comment
• 0 votes

Answered

PCMCIA SLOT

1. Community
2. Troubleshooting — FANUC

Hi All ,  Whenever i try to do anything on memory card . Error message appears and says , "CARD UNMOUNTED"  Do anyone faces the same issue ?  I am using following card. Please help     

• Created February 02, 2020 06:00
• 3 followers
• 2 comments
• 0 votes

Answered

Pickup tool - EOAT

1. Community
2. Mechanical Design

Hey Everyone ,  We have a plant of corrugated box making. There is no specific size of box. The process is like we have a roll of corrugated carboard. It is mounted on the corrugated board cutting ...

• Created February 01, 2020 11:17
• 2 followers
• 2 comments
• 0 votes

FUSE BLOWN

1. Community
2. Electrical Design

Hi All ,  I may have a really dumb question. I handle mechanical tasks but this is first time i need to handle electrical equipment. So my question is about fuse. I had SRVO-213 alarm and there is ...

• Created February 01, 2020 06:34
• 2 followers
• 2 comments
• 0 votes