Charlotte Perrier

1. Community
2. Troubleshooting — FANUC
3. USB STICK Size - R30iB

Ching Marenco I am not sure about the maximum size is supported . But Fanuc has validated following PenDrive which can be used on R30iB controller.  1. RUF-C2GS/U2 of BUFFALO INC. 2. TB-ST2/2G and ...

• View comment
• Created February 17, 2020 14:37
• 0 votes

1. Community
2. Troubleshooting — FANUC
3. MACR-016 "The macro is not completed"

Fredric Demps The meaning of this error is that it was aborted while execution. If you have not done anything i.e. editing in programs or changed I/O configuration, There is strong chances that the...

• View comment
• Created February 17, 2020 13:10
• 0 votes

1. Community
2. Troubleshooting — FANUC
3. Please Power off , If you want to recover

Ching Marenco There can be issue with the Servo Amplifier or FSSB circuit. 1. Check Fuses on Servo Amp.  2. Check you FSSB module , If you have no power there will be no LEDs Blinking  3. Check Opt...

• View comment
• Created February 17, 2020 12:59
• 0 votes

1. Community
2. Electrical Design
3. Teach Pendant Part Number

Losev Radinovich Based on your robot category teach pendant defined as under. 1. A05B-2255-C101#ENG  --  ENGLISH GENERAL 2. A05B-2255-C101#EMH  -- MATERIAL HANDLING  3. A05B-2255-C101#ESW  -- SPOT ...

• View comment
• Created February 13, 2020 10:40
• 0 votes

1. Community
2. Electrical Design
3. SRVO-004 Fence Open Alarm

Chadwick Dockstader If you have done the fencing wiring with hard wire method. - Check all the wire connection. - Check the shielding of wires if there are any cuts. - Check safety relays / contact...

• View comment
• Created February 13, 2020 09:29
• -1 votes

1. Community
2. Mechanical Design
3. Welding Nozzle Cleaning

Fredric Demps There are many companies provides reaming operation on nozzle parts. To get more idea on cleaning process refer this video link and post about it. I hope it will be really helpful. 1....

• View comment
• Edited February 13, 2020 09:05
• 0 votes

1. Community
2. Troubleshooting — FANUC
3. Mig Welding Cleaning Station

Vicky Kanne   1> The frequency of reaming operation depends on your production cycle and operation. Reaming too frequently will waste your production time similarly if reaming operation is infreque...

• View comment
• Created February 13, 2020 08:53
• 0 votes

1. Community
2. Troubleshooting — FANUC
3. Config Menu

For your information , Configuration menu is not available for RJ2 Controller.   

• View comment
• Edited February 09, 2020 14:10
• 0 votes

1. Community
2. Mechanical Design
3. Wiring Harness Replacement

Yes , It is possible. At some places , Before removing old cable harness , attach new cable with it. So when you pull the old cable , the new will get also replaced by sliding at same place. There ...

• View comment
• Created February 07, 2020 09:54
• 0 votes

1. Community
2. Troubleshooting — FANUC
3. The Wall Mount FANUC

I do not see any image , However kindly follow below steps to change your mounting angle    Perform Controlled start  Follow below thread for how to perform controlled start .  https://forum.diy-ro...

• View comment
• Created February 06, 2020 09:33
• 0 votes