Chadwick Dockstader

System option disabled

1. Community
2. Troubleshooting — FANUC

Hello Everyone ,  I do not find system option in the screen. How to get it back ? RJi3B

• Edited January 31, 2020 07:28
• 2 followers
• 1 comment
• 0 votes

Answered

Discontinuing Service of Robot

1. Community
2. Troubleshooting — FANUC

Hi ,  We have LRMATE 2000i. and couple of many robots. As of now we have low working frequency and to make the work floor more spacious , we are planning to move one of robot into inventory room. I...

• Created January 30, 2020 16:27
• 2 followers
• 1 comment
• 0 votes

PLC Connection

1. Community
2. Electrical Design

Hi,  I am not sure at which rack number i should connect PLC to robot ?  As well as do anyone has description of all racks. i.e. Which rack is used for which purpose ? Thanks a lot .  

• Edited January 29, 2020 18:38
• 5 followers
• 5 comments
• 0 votes

Spot Welding Tip Clean

1. Community
2. Troubleshooting — FANUC

Hi All  I have fanuc robot M-420IA , With R30iB controller. Basically I am using it for the Spot welding. So as 12 cycles completes, I need to clean the tip but every time it requires to touch up t...

• Edited January 28, 2020 10:00
• 2 followers
• 1 comment
• 0 votes

Answered

Mastering Issue

1. Community
2. Troubleshooting — FANUC

Hi ,  We have M20iA with R30iB controller. It was a battery failure. Someone just ignored BZ alarm. As normal procedure , mastering is required when you have a battery failure. So When we approache...

• Created January 28, 2020 04:54
• 2 followers
• 1 comment
• 0 votes

iR Calibration Signature

1. Community
2. Troubleshooting — FANUC

We have few robots , They are working really good since long time. We have been doing the regular maintenance on timely. Yet , There is an error of 0.3 mm. We basically run the same program on all ...

• Created January 25, 2020 15:50
• 2 followers
• 1 comment
• 0 votes

Answered

Multiple Robot Connection

1. Community
2. Electrical Design

Hello ,  Is it anyway i can connect multiple fanuc robot with single PLC and PLC to be connected to computer  OR Direct connection to the computer. So i can manage all robot seating at one place. N...

• Created January 24, 2020 12:18
• 2 followers
• 2 comments
• 0 votes

Answered

Beep Sound

1. Community
2. Troubleshooting — FANUC

At my workplace , previous operate disabled the beep sound on ipendant !!  How can i restore it  ?  

• Edited January 22, 2020 09:56
• 3 followers
• 2 comments
• 0 votes

Inaccurate path

1. Community
2. Troubleshooting — FANUC

Hello Experts ,  I have a welding fixture and programmed the welding path accordingly. After running the production cycle for few days , I always required to reteach the points or adjust the fixtur...

• Created January 21, 2020 12:48
• 3 followers
• 3 comments
• 0 votes

Answered

CRMA15 & CRMA16 connection

1. Community
2. Electrical Design

Hello ,  I am looking for connection help with CRMA I/O. Can anyone help me with this. R30iB Thanks a lot 

• Edited January 21, 2020 04:44
• 2 followers
• 2 comments
• 0 votes