Avatar

Ernesto Perito

  • Total activity 122
  • Last activity
  • Member since
  • Following 0 users
  • Followed by 0 users
  • Votes 30
  • Subscriptions 38
Follow

Posts

Recent activity by Ernesto Perito
Sort by recent activity Recent activity Votes
  • Answered

    Device Net errors

    1. Community
    2. Troubleshooting — FANUC

    Hello everyone, I Need a little help, on my Fanuc S-430i RJ3 Robot. I am connecting  24 VDC to the card for power the devicenet I am having these Device net error DNET-119 Dup. Mac Ack Fault. And i...

    • Created
    • 3 followers
    • 3 comments
    • 0 votes

  • “13007 Reset already in progress” error

    1. Community
    2. Troubleshooting — FANUC

    Dear members, I cant move any robot axis. I am getting this “13007 Reset already in progress” error on my Fanuc S-420F.  What should i do to clear this error?

    • Created
    • 2 followers
    • 1 comment
    • 0 votes
  • Answered

    Controlled start to normal operation

    1. Community
    2. Troubleshooting — FANUC

    Hi, I performed a control start on my R30iA Mate controller. Now I am kind of stuck in the controlled start and unable to go back to the normal operation :/ idk what is happening I have tried power...

    • Created
    • 3 followers
    • 3 comments
    • 0 votes

  • Hot Start

    1. Community
    2. Electrical Design

    Hi Members, I have tried searching the forum, I am sure you guys can guide me here. I am looking for brief introduction of HOT START and its complete procedure. Actually i am working for recovery i...

    • Edited
    • 2 followers
    • 2 comments
    • 0 votes

  • Unregistered UFrame Error

    1. Community
    2. Troubleshooting — FANUC

    Hi, I am working with an R2000iC Robot R30iA Controller with DCS. I am getting an error of unregistered UFrame on entering a user frame while I set up a Cartesian position Check. I have not found a...

    • Created
    • 2 followers
    • 2 comments
    • 0 votes
  • Answered

    New program not running

    1. Community
    2. Troubleshooting — FANUC

    Hi Guys, I have a problem with my M-16iA with R-J3iB Controller. We are trying to update the program, a bit changed one as per operations requirement. But the robot is not running on the new select...

    • Created
    • 4 followers
    • 3 comments
    • 0 votes
  • Answered

    Display Cycle Time

    1. Community
    2. Troubleshooting — FANUC

    Hi Everyone, I am working a on Fanuc robot which is not showing cycle time. As far as i know fanuc robots normally display cycle time under the registers..Can anyone help me displaying a live cycle...

    • Created
    • 2 followers
    • 1 comment
    • 0 votes
  • Answered

    M10iA: Multiple errors

    1. Community
    2. Troubleshooting — FANUC

    Our M10iA is detecting collisions with its Axis 2 when it is in running condition or in jogging, while in actually there was not any collisions. I am getting Multiple errors like: SRVO-050 ERROR SR...

    • Created
    • 3 followers
    • 3 comments
    • 0 votes

  • 24 V Connections through robot

    1. Community
    2. Electrical Design

    Hi Everyone, I am trying to control (switch on and off) an LED (24V) through my robot's OUTPUT,(I KNOW HOW TO DO IT THROUGH TP). Actually i need to know the location of the outputs in the cabinet.....

    • Created
    • 3 followers
    • 3 comments
    • 0 votes
  • Answered

    SRVO-073

    1. Community
    2. Troubleshooting — FANUC

    Hi Everyone! I am struggling with an error on my robot. It reads CMAL ALARM SRVO-073, On reset of pulse encoder alarm resets but I am repeatedly getting this alarm when i try to move robot's axis 4...

    • Created
    • 3 followers
    • 2 comments
    • 0 votes