Mathieu Berube

1. Community
2. Programming — FANUC
3. Program Timer not running

Hi Sylvain, A good way is to have a program that start this timer at the power up of the robot. This program should look like this: To make it run at the boot of the robot, Go to MENU - NEXT - SYS...

• View comment
• Created March 15, 2022 21:30
• 2 votes

1. Community
2. Troubleshooting — FANUC
3. error XML perse CRX10-ia/L

Hi Manvel, Have you changed the IP Adress of the tablet to connect it to your network? 

• View comment
• Created March 24, 2025 11:46
• 0 votes

1. Community
2. Troubleshooting — FANUC
3. Fanuc Robot Ref. Pos. for Quick Mastering Not Set

Hi Rodrigue,   Bring the robot at Zero position mark on all axis and do a SET QUICK MASTER REF. To perform that, go to MENU - NEXT - SYSTEM - 3 Master/Cal Inside the Master/Cal menu, place the cur...

• View comment
• Created November 06, 2023 15:27
• 1 vote

1. Community
2. Troubleshooting — FANUC
3. CRX not moving when Enable UI Signals is TRUE

Hi John68,   Is your UI signal configured like this? Also, check if UI[8] (Enable) is at ON.   DIY-Robotics productshttps://diy-robotics.com/products/

• View comment
• Edited May 24, 2022 17:50
• 1 vote

1. Community
2. Troubleshooting — FANUC
3. SYST-322 Auto status check time out

Hi Sylvain, The collaboratives robots from Fanuc need to do this auto status check every 90 sec when the robot is moving continually. If you want the robot to continue running without having to sta...

• View comment
• Created May 20, 2022 11:55
• 0 votes

1. Community
2. Troubleshooting — FANUC
3. Error Roboguide V9 Rev N

Hi Adrien, Do you have the WeldPro liscence activated? To check that, open the License Manager, the WeldPro should be green and registered

• View comment
• Created March 17, 2022 11:55
• 1 vote

1. Community
2. Programming — FANUC
3. Robot Offset PR[] error

Hi John68, Here's the procedure to adjust the mastering for J2 and J3. 1. In your program J23, go to P[2] so the robot is flipped over on J3. 2. Move the robot in Joint mode only moving J2 and J3 ...

• View comment
• Created March 15, 2022 20:17
• 1 vote

1. Community
2. Programming — FANUC
3. Robot Offset PR[] error

Hi John68, This drift may occur when the mastering of the robot is not properly done. To validate it, you need to check if the robot return to the same position when you change the config of the po...

• View comment
• Created March 11, 2022 13:10
• 1 vote

1. Community
2. Troubleshooting — FANUC
3. INTP-105/PROG-040 Run request failed/locked by another task

Hi, I've seen this error when you try to run two motion programs at the same time. The program open gripper needs to be in no motion mode. Press SELECT and on the 'open gripper' program press NEXT ...

• View comment
• Created August 04, 2021 12:02
• 1 vote

1. Community
2. Electrical Design
3. New to the Fourm. Looking for some guidance with Euromap 73.

Hi Raymond, The Euromap 73 is usually used for the External Safety Device like replacing the back door of the IMM with your fences. If you are looking to replace the Euromap 12 function (Mold Open,...

• View comment
• Created March 11, 2021 14:00
• 1 vote